electric radiant floor heating systems under fir wood floor

ELECTRIC RADIANT FLOOR HEATING SYSTEMS UNDER FIR WOOD FLOOR DOWNLOAD
ELECTRIC RADIANT FLOOR HEATING SYSTEMS UNDER FIR WOOD FLOOR WINDOWS

Electric systems are high temperature systems with the heat highly concentrated on the electrical filament. Electric radiant heat systems are NOT accepted by Hallmark Floors for use under hardwood flooring. Are electric radiant heat systems OK for Hallmark Wood Floors?Ī. Good systems will not have temperature variations exceeding 3º F within a 2’ radius. Hydronic radiant heat systems that do not include thermal mass or aluminum transfer sheets will not provide even distribution of heat. Only the systems that ensure a very even distribution of heat. Are all hydronic systems OK for use with Hallmark Wood Floors?Ī. NOTE: All systems should have a fail-safe to ensure that the surface of the floor never exceeds the recommended surface temperature of 85º F. Rooms with high ceilings may require radiant heat to be installed in the ceilings and ceiling fans mounted to circulate the air. Rooms with high ceilings can create a situation where the floors can become too warm due to the high volume of space to be heated. When ceilings exceed 10’ high, the amount of cubic air that needs to be heated can create problems for a hardwood floor. Radiant floor heating is very efficient but does have some limitations. Are there any design limitations you need to be aware of?Ī.

ELECTRIC RADIANT FLOOR HEATING SYSTEMS UNDER FIR WOOD FLOOR DOWNLOAD

Download – Radiant Floor Heating Education Guide Consult a radiant specialist for proper design. Consult a radiant specialist for proper design.Ĭonceptual diagram, see following pages for actual systems. Energy is released to warm the room and cool water returned to the boiler to be reheated.Ĭonceptual diagram, see following pages for actual Hydronic radiant heat is a system that uses warm water driven through a tube network. An exterior thermostat should be used for radiant floor heating.Ī. This allows the temperature to be increased slowly with less shock to the floor. Radiant heat should be turned on at low power in the fall and the heat increased gradually. Should radiant heat be turned on before weather becomes cold?Ī. Place the material on site 24 hours prior to installation. As such long acclimation times are not required. Since the floor is engineered, as such it is pre-acclimated to a 30 to 55% environment.

This varies by geography but is usually defined by areas that experience long periods of freezing weather or have naturally low humidity like the deserts or higher elevations present in the mountains (below 30% humidity).Ī. What constitutes a low humidity environment?Ī. Good humidity control can minimize these changes even more with radiant floor heating. However, engineered hardwood floors are far more proportionally stable than solid hardwood floors. Hardwood flooring is a natural product and will change size with variations in temperature and moisture content. Do the floors gap or expand and contract?Ī. A floating floor with have a degree of resilience, or give that a nail-or-glue-down floor does not have. The lightweight concrete moisture content must not exceed 1.5% as measured with a Tramax Moisture Encounter meter.Ī. What should the moisture content of the lightweight concrete be before installation?Ī. The home should be aired out briefly everyday to allow excess humidity from the thermal mass to exhaust moisture out of the structure. Two to three weeks prior to installation of the hardwood flooring with the thermostat set at 70º F and then at 85º F for 3 more days. How long before installation of the floor should the radiant heat system be powered on?Ī. The relative humidity conditions must be between 30 and 55%, and the temperature between 65 and 85 degrees F. Kitchen cabinets must be in place prior to installation of the floor. If the tubing is encased in lightweight concrete, the concrete must be completely dry.

ELECTRIC RADIANT FLOOR HEATING SYSTEMS UNDER FIR WOOD FLOOR WINDOWS

All windows and doors must be in place and the structure completely weather tight. Hardwood flooring should be the last item installed on the radiant heat floor project. At what point should a Hallmark Floors hardwood floor be installed?Ī.

Radiant Heat Systems: In-floor heating systems must be water based, and designed to prevent the surface temperature of the hardwood floor from exceeding 85º F. Radiant Heat FAQ – Frequently Asked Questions

Electric radiant floor heating systems under fir wood floor